Alphacan Omniplast - Primus HL SN12 (Wastewater)
Produktbild
Desafortunadamente, no puedes comprar este artículo con nosotros.
Crassus proporciona este sistema de tuberías estrictamente por razones informativas dentro del contexto del Léxico de Tuberías.

Dimensión
Extremo del tubo
Propiedades
Categoría de material Plástico
RXNR 27-9-S
Designación Alphacan Omniplast - Primus HL SN12 (Wastewater)
Fabricante Omniplast Deutschland GmbH
DN 300
Extremo del tubo Extremo puntiagudo
Nombre del material Hart-PVC (PVC-U)
Color (exterior) Naranja
Aplicaciones Haustechnik, Ingeniería civil
Dimensionamiento
ID (mm) 296
DE (mm) 315
Descripción

The philosophy of Alphacan Omniplast is to manufacture ready-to-install pipe systems that are smooth inside and out, which can be easily and easily assembled, filled and compacted into a pipeline. Thanks to its high ring stiffness (≥ 12 kN / m²) and longitudinal stiffness and the molded socket, the Primus HL SN 12 pipe system offers extraordinary stability and security with very good assembly capability and simple installation properties. Due to the clear color separation, sewage pipes in clay-brown and rainwater pipes in blue, it is easy to distinguish between sewage and rainwater even after decades of inspection.

PRIMUS HL SN 12 is the full wall high load sewer pipe system according to the standard of the oldest plastic pipe producer in Germany. Due to the complete fulfillment of all requirements of DIN EN 1401-1, Primus HL SN 12 has unlimited building authority approval. As a technically mature standard material in civil engineering, PVC-U has an extraordinarily high chemical resistance and is not attacked by any of the substances that may occur in wastewater.

The material:

Through the consistent use of the highest quality PVC new material and the production-technical know-how of the oldest plastic pipe producer in Germany, the ring stiffness of ≥ 12 kN / m² according to ISO 9969 for all components of the solid wall sewer pipe system Primus HL SN 12 was achieved through an independent technical solution. The material parameters were decidedly improved, but the required amount of material was not increased. Compared to a standard PVC material, for example, the E-module of the Primus HL SN 12 has been increased from around 3000 N / mm² to well over 4000 N / mm²! This significant material improvement in connection with the low creep factor also achieved the corresponding long-term ring stiffness according to DIN 16961. Should any repair work arise, you can fall back on the inexpensive and flexible Crassus range, which is known for its interior and exterior solutions.

Chemical resistance:

As a technically mature standard material in civil engineering, PVC-U has an extraordinarily high chemical resistance and is not attacked by any of the substances that may occur in wastewater. Any biogenic sulfuric acid, mineral oils, fats and fuels that may develop, but also other chemicals such as acids or alkalis, do not damage PVC-U, unlike other known pipe materials.

Connection option to other sewage systems:

Crassus hose adapters, Crassus combi adapters, Crassus adapter couplings, Crassus rubber adapters as well as bends, branches, Crassus end caps and much more.

Pipe repair:

Crassus Pipe Doctor and Crassus Pipe Plaster

Source: Omniplast, Crassus

Conexiones de tubería flexible
CRA17200
Acoplamiento adaptador CAC 3204
295-320 mm | 144-160 mm
hasta 0.6 bar / 8.7 PSI
CRA17201
Acoplamiento adaptador CAC 3205
295-320 mm | 170-192 mm
hasta 0.6 bar / 8.7 PSI
CRA17206
Acoplamiento adaptador CAC 3207
295-320 mm | 210-235 mm
hasta 0.6 bar / 8.7 PSI
CRA17207
Acoplamiento adaptador CAC 3208
295-320 mm | 240-265 mm
hasta 0.6 bar / 8.7 PSI
CRA17208
Acoplamiento adaptador CAC 3209
295-320 mm | 265-290 mm
hasta 0.6 bar / 8.7 PSI
CRA17209
Acoplamiento adaptador CAC 3351
310-335 mm | 180-205 mm
hasta 0.6 bar / 8.7 PSI
CRA17212
Acoplamiento adaptador CAC 3600
335-360 mm | 295-320 mm
hasta 0.6 bar / 8.7 PSI
CRA17215
Acoplamiento adaptador CAC 3850
360-385 mm | 300-325 mm
hasta 0.6 bar / 8.7 PSI
CRA16224
Acoplamiento estándar (reforzado) CSC 320
295-320 mm
hasta 2.5 bar / 36.3 PSI
CRA16225
Acoplamiento estándar (reforzado) CSC 335
305-335 mm
hasta 2.5 bar / 36.3 PSI
CRA16226
Acoplamiento estándar (reforzado) CSC 345
315-345 mm
hasta 2.5 bar / 36.3 PSI
CRA16224FKM
Acoplamiento estándar (reforzado) CSC 320 FKM
295-320 mm
hasta 2.5 bar / 36.3 PSI
CRA16225FKM
Acoplamiento estándar (reforzado) CSC 335 FKM
305-335 mm
hasta 2.5 bar / 36.3 PSI
CRA16903
Acoplamiento estándar (reforzado) CSC XL 320
295-320 mm
hasta 2.5 bar / 36.3 PSI
CRA16904
Acoplamiento estándar (reforzado) CSC XL 335
305-335 mm
hasta 2.5 bar / 36.3 PSI
CRA16905
Acoplamiento estándar (reforzado) CSC XL 345
315-345 mm
hasta 2.5 bar / 36.3 PSI
Productos especiales
CRA15769
Tapa exterior CEC 315
300-315 mm
hasta 0.6 bar / 8.7 PSI

Importante: Todos los nombres de marcas y marcas comerciales mencionados en este sitio web son propiedad de sus respectivos propietarios. La mención de estos nombres y términos es solo para fines informativos y no implica ninguna cooperación o asociación con los respectivos fabricantes (uso nominativo). La información y las descripciones proporcionadas sirven como una visión general general y no constituyen un asesoramiento o recomendación de productos vinculante. A pesar de una investigación cuidadosa, no se garantiza la integridad, exactitud o actualidad del contenido. Todas las imágenes mostradas (imágenes de productos, gráficos, etc.) fueron creadas por Crassus GmbH & Co. KG o reproducidas con fines de demostración. Pueden diferir del producto original. No se acepta ninguna responsabilidad por daños materiales o inmateriales causados por el uso o no uso de la información proporcionada o por el uso de información incorrecta o incompleta. Si los textos o información del fabricante se resumen o citan con nuestras propias palabras, esto se hace de una manera que respeta los derechos de autor de los respectivos titulares de derechos. El uso posterior del contenido publicado aquí requiere nuestro consentimiento expreso y, si es necesario, la aprobación del respectivo titular de los derechos.