Press Seal Type CMS30-E

Against pressing water and non-pressing water

Water-tight welded bolts for an optimum of steadiness and corrosion protection

Custom-made for customer-specific requirements

100% gas-, odor- and waterproof

In different material versions available

All products in 48h producible

Proof of pressure-tightness

Figure
 
Item number
 
A | Core drill hole
(mm)
B | Pipes / Cables ø
(mm)
L | Seal
(mm)
Material
 
Pressure-tight
(bar)
Thightning torque
(Nm)
Data sheet
 
CRA21191GGV 50 0-25 30 EPDM / GGV 2.5 - PDF
CRA21191V2A 50 0-25 30 EPDM / V2A 2.5 - PDF
CRA21191V4A 50 0-25 30 EPDM / V4A 2.5 - PDF
CRA21192GGV 60 0-35 30 EPDM / GGV 2.5 - PDF
CRA21192V2A 60 0-35 30 EPDM / V2A 2.5 - PDF
CRA21192V4A 60 0-35 30 EPDM / V4A 2.5 - PDF
CRA21193GGV 70 0-45 30 EPDM / GGV 2.5 - PDF
CRA21193V2A 70 0-45 30 EPDM / V2A 2.5 - PDF
CRA21193V4A 70 0-45 30 EPDM / V4A 2.5 - PDF
CRA21194GGV 80 0-55 30 EPDM / GGV 2.5 - PDF
CRA21194V2A 80 0-55 30 EPDM / V2A 2.5 - PDF
CRA21194V4A 80 0-55 30 EPDM / V4A 2.5 - PDF
CRA21195GGV 100 0-75 30 EPDM / GGV 2.5 - PDF
CRA21195V2A 100 0-75 30 EPDM / V2A 2.5 - PDF
CRA21195V4A 100 0-75 30 EPDM / V4A 2.5 - PDF
CRA21196GGV 125 0-100 30 EPDM / GGV 2.5 - PDF
CRA21196V2A 125 0-100 30 EPDM / V2A 2.5 - PDF
CRA21196V4A 125 0-100 30 EPDM / V4A 2.5 - PDF
CRA21197GGV 150 0-125 30 EPDM / GGV 2.5 - PDF
CRA21197V2A 150 0-125 30 EPDM / V2A 2.5 - PDF
CRA21197V4A 150 0-125 30 EPDM / V4A 2.5 - PDF
CRA21198GGV 200 0-175 30 EPDM / GGV 2.5 - PDF
CRA21198V2A 200 0-175 30 EPDM / V2A 2.5 - PDF
CRA21198V4A 200 0-175 30 EPDM / V4A 2.5 - PDF
CRA21199GGV 250 0-225 30 EPDM / GGV 2.5 - PDF
CRA21199V2A 250 0-225 30 EPDM / V2A 2.5 - PDF
CRA21199V4A 250 0-225 30 EPDM / V4A 2.5 - PDF
CRA21200GGV 300 0-275 30 EPDM / GGV 2.5 - PDF
CRA21200V2A 300 0-275 30 EPDM / V2A 2.5 - PDF
CRA21200V4A 300 0-275 30 EPDM / V4A 2.5 - PDF
CRA21201GGV 350 0-325 30 EPDM / GGV 2.5 - PDF
CRA21201V2A 350 0-325 30 EPDM / V2A 2.5 - PDF
CRA21201V4A 350 0-325 30 EPDM / V4A 2.5 - PDF
CRA21202GGV 400 0-375 30 EPDM / GGV 2.5 - PDF
CRA21202V2A 400 0-375 30 EPDM / V2A 2.5 - PDF
CRA21202V4A 400 0-375 30 EPDM / V4A 2.5 - PDF
CRA21203GGV 450 0-425 30 EPDM / GGV 2.5 - PDF
CRA21203V2A 450 0-425 30 EPDM / V2A 2.5 - PDF
CRA21203V4A 450 0-425 30 EPDM / V4A 2.5 - PDF
CRA21204GGV 500 0-475 30 EPDM / GGV 2.5 - PDF
CRA21204V2A 500 0-475 30 EPDM / V2A 2.5 - PDF
CRA21204V4A 500 0-475 30 EPDM / V4A 2.5 - PDF

Problem

You have pipes/cables which must through a waterproof concrete wall. The feed-through must prevent the ingress of odor, gas or water.


Solution (1/4)

Place the divided Press Seal CMS30-E around the pipe/cable.


Solution (2/4)

Push the Crassus Press Seal Type CMS30-E into the cleaned up wall sleeve (alternative: core drill hole).


Solution (3/4)

Tighten the screws in the following manner, always two diagonally opposite nuts are tightened in succession. Pay attention to the recommended tightening torque.


Solution (4/4)

Done! The feed-through prevents ingress of odor, gas or water.